Minda Industries Limited – Electronics Division

Our Products

Position Sensor Technology

pro4

ROTARY POSITION SENSOR

To detect rotary position of gear shifting drum in gear box. It also convert Angular position into analog voltage signal and 3600 Rotary Position Sensing Throttle Position, Motor Shaft Position. It is suitable for E-scooters & Motorcycles

  • Absolute Rotary Position Sensing
  • Robust Magnetic Design
  • Programmable angular range upto 360Deg
  • Analog, Ratio metric Output

pro4

DOOR POSITION SENSOR

To sense the position of Door and Emergency exit window

  • Non Contact Type
  • Sealed design - IP67
  • Adjustment for play in assembly on Vehicle
  • Short Circuit Protected Output
  • Fast Response

pro4

CLUTCH PEDAL POSITION SENSOR

To give output signal when Clutch Pedal is operated. It is suitable for 4 wheeler & commercial vehicles.

  • Non Contact Type
  • Sealed design - IP67
  • Short Circuit Protected Output
  • Fast Response
  • Active sensor
  • Automotive Protection – ISO7637-2

pro4

NEUTRAL POSITION SENSOR

To accurately detect Neutral Gear Position of vehicle and provide protected output signal (PWM) to ESS ECU.

  • Non Contact Type
  • Sealed design - IP67
  • Short Circuit Protected Output
  • Fast Response
  • Adjustment for play in assembly on Vehicle
  • Automotive Protection – ISO7637-2

pro4

DOOR SAFETY SENSOR

To sense the position of Door, Rear engine side lid & lid of fuel filling area

  • Non Contact Type
  • Sealed design - IP67
  • Adjustment for play in assembly on Vehicle
  • Short Circuit Protected Output
  • Fast Response

Speed Sensor Technology

pro4

SPEED SENSOR

Rotation detection sensor for motorcycles & automobiles. It is suitable for ABS wheel speed, transmission speed detection.

  • Digital current sinking outputs (Open collector)
  • Excellent low speed performance.
  • Wide range of operating temperature
  • Simple construction easy to assemble

pro4

SPEED SENSOR

This sensor is mounted in transmission box to sense the vehicle speed and give the output to instrument cluster and engine control unit.

  • Digital current sinking outputs.
  • Excellent low speed performance
  • Wide range of operating temperature
  • Simple construction easy to assemble
  • Sealed Design – IP67

pro4

GEAR TOOTH SPEED SENSOR

To detect rotating position of Crankshaft for motorcycles & automobiles. It also detect engine speed and occurrence of a Misfire

  • Non contact type (Hall IC based)
  • Robust Design
  • Sealed design (IP 67)
  • Suitable for High temperature
  • Zero speed detection possible

pro4

CRANKSHAFT POSTION SENSOR

These sensors are mounted in Two Wheeler front wheel hub to sense the vehicle speed and give the output to instrument cluster.

  • Non contact type (Inductive based)
  • Robust Design
  • Sealed design (IP67)
  • Suitable for high temperature

pro4

CAMSHAFT POSTION SENSOR

To detect rotating position of Camshaft for motorcycles & automobiles.

  • Non contact type (Hall IC based)
  • High reliability, No moving parts
  • Zero speed detection
  • Sealed design(IP67)
  • Single screw mounting
  • Suitable for High temperature

Wireless Technology

pro4

TIRE PRESSURE MONITORING SENSOR

To monitor tire air pressure & warn driver if one or more tire pressure falls below a specific level.

  • Light weight and Compact Design
  • Accurate tire pressure measurement +/- 1PSI
  • Monitoring tyre pressure anytime
  • High accuracy
  • Not affected by bumpy roads
  • Detects both under inflated and over inflated tyres
  • Expands tyre lifespan
  • Saves fuel consumption
  • Improves safety
  • Easy to install

Mutiplexing Technology

pro4

MULTIPLEXING CONTROLLER

Multiplexing BCM provides intelligence to controls the vehicle electrical loads such as Turn Indicator (LED), Headlamp control, Intelligent starter, Horn Control, Engine stop function

  • Protected output
  • Very low current consumption in sleep mode
  • Battery saving function
  • Solid State control
  • Active current sense eliminates fuses

pro4

DC – DC CONVERTOR

To provide regulated power supply to ECU where voltage regulation is from 24V DC to 12V DC

  • Efficiency more than 90%
  • Low Battery Cut Off
  • Output Short Circuit & Load Dump Protection
  • High Temperature Resistant
  • Dual purpose heat sink
  • Robust housing
  • Sealed Connector
  • Ripple free regulation

Actuator Technology

pro4

HEADLAMP LEVELLING MOTOR

Head Lamp Leveling Motor is an Actuator, Used to position the headlamp level to adjust Head Lamp beam angle on road

  • Highly reliable
  • Low noise
  • Sealed coupler
  • Automotive Protections
  • Adjustable Shaft
  • Wheel type mechanism for fast manual adjustment

Magnetics Technology

pro4

ELECTRONIC ACCELERATOR PEDAL MODULE

The accelerator pedal module converts the driver’s accelerator pedal effort to an electric signal, and sends the signal to the engine ECU, which controls engine power and acceleration

  • Non Contact type – Hall Effect Sensor
  • Sealed design - IP 67
  • Precise sensing
  • Qualified for Automotive application
  • Dual Redundant output
  • Long life and high reliability
  • Small size and light weight

Lighting Technology

pro4

HID LIGHTING SYSTEM

To enhance head light efficiency by use of HID lighting system, which will consume less power & save fuel

  • Produces more than twice as much light output as conventional halogen lights
  • Brighter White light
  • High color temperature, similar to natural daylight – > 4500K
  • Enhance the aesthetic character of vehicle design and promote brand recognition
  • Consume up to 30% less energy than standard halogen lamps
  • Light diffraction is reduced to a minimum
  • Auto leveling & headlamp cleaning can be avoided at <= 2000lm

Angle Sensor Technology

pro4

BRAKE PEDAL ANGLE SENSOR

Brake pedal sensor is used in hybrid vehicles which generates output signal proportional to pedal travel

  • Non Contact type – Hall Effect Sensor
  • Diagnostics mode
  • Sealed design - IP 67
  • Precise sensing
  • Qualified for Automotive application
  • Redundant output
  • Snap mounting, no fastener required for holding & locating

pro4

ROLL OVER SENSOR

Roll Over Sensor indicates to stop the engine in case of vehicle roll over

  • Non contact type
  • Pendulum type design
  • Sealed design (IP67)
  • Short circuit protection
  • Coupler removal detection
  • Short to ground detection
  • Short to battery supply detection
  • Single screw mounting

Pressure Sensor Technology

pro4

AIR FLOW

To control air flow to engine by checking inlet manifold air pressure. It alsosupply required Air/Fuel charge to Engine and sense change in intake manifold pressure & provide necessary signal to ECU

  • Sealed design ( IP 67 )
  • Resistant to high humidity & common Automotive media
  • Improved accuracy at high temperature
  • Piezoresistive sensor element

Thermistor Technology

pro4

TEMPERATURE SENSOR

To sense the engine & oil temperature and give feedback to ECU. Temperature detection for motorcycles & automobiles

  • Sealed design IP 67
  • Robust design
  • Thermistor technology
  • Fast response to temperature
  • Isolated to ground